The MP 40 descended from its predecessor the MP 38, which was in turn based on the MP 36,
a prototype made of machined steel. The MP 36 was developed independently by Erma
Werke's Berthold Geipel with funding from the German Army. It took design elements
from Heinrich Vollmer's VPM 1930 and EMP. Vollmer then worked on Berthold Geipel's MP 36
and in 1938 submitted a prototype to answer a request from the Heereswaffenamt (Army
Weapons Office) for a new submachine gun, which was adopted as MP 38. The MP 38 was a
simplification of the MP 36, and the MP 40 was a further simplification of the MP 38, with
certain cost-saving alterations, most notably in the more extensive use of stamped steel rather
than machined parts.
The MP 40 was often called the "Schmeisser" by the Allies, after the weapon designer Hugo
Schmeisser. Schmeisser had designed the MP 18, which was the first mass-produced
submachine gun. He did not, however, have anything to do with the design or development of
the MP 40, although he held a patent on the magazine
The MP 40 submachine guns are open-bolt, blowback-operated automatic arms. The only
mode of fire was fully automatic, but the relatively low rate of fire enabled single shots with
controlled trigger pulls. The bolt features a telescoping return spring guide which serves as a
pneumatic recoil buffer. The cocking handle was permanently attached to the bolt on early MP
38s, but on late production MP 38s and MP 40s, the bolt handle was made as a separate
part. It also served as a safety by pushing the head of the handle into one of two separate
notches above the main opening; this action locked the bolt either in the cocked (rear) or
uncocked (forward) position. The absence of this feature on early MP 38s resulted in field
expedients such as leather harnesses with a small loop that were used to hold the bolt in the
forward position.
The MP 38 receiver was made of machined steel, but this was a time-consuming and
expensive process. To save time and materials, and thus increase production, construction of
the MP 40 receiver was simplified by using stamped steel and electro-spot welding as much as
possible. The MP 38 also features longitudinal grooving on the receiver and bolt, as well as a
circular opening on the magazine housing. These features were eliminated on the MP 40.
One unique feature found on most MP 38 and MP 40 submachine guns was an aluminum,
steel, or Bakelite resting bar or support under the barrel. This was used to steady the weapon
when firing over the side of open-top armored personnel carriers such as the Sd.Kfz. 251 halftrack.
A hand guard, made of a synthetic material derived from Bakelite, was located between
the magazine housing and the pistol grip. The barrel lacked any form of insulation, which often
resulted in burns on the supporting hand if it was incorrectly positioned. The MP 40 also had a
forward-folding metal stock, the first for a submachine gun, resulting in a shorter overall
weapon when folded. However, this stock design was at times insufficiently durable for hard
combat use.
Cartridge 9×19mm Parabellum
Effective firing range: 100–200 m
Maximum firing range: 250 m
Rate of fire: 500–550 rounds/min
Place of origin: Nazi Germany
Barrel length: 251 mm (9.9 in)
Overall length 833 mm (32.8 in) stock extended, 630 mm (24.8 inches) stock folded
Weight 3.97 kg (8.75 lb
Unit cost: 57 RM (1940); 230 EUR current equivalent
Designer: Heinrich Vollmer; Berthold Geipel
Produced 1940–1945
No. built 1,100,000 (estimated
Manufacturer Steyr-Mannlicher
Erma Werke
Haenel
Variants MP 36
MP 38
MP 40
MP 40/1
MP 41
A modern round consists of the following:
1. bullet, as the projectile;
2. cartridge case, which holds all parts together;
3. propellant, for example gunpowder or cordite;
4. rim, which provides the extractor on the
firearm a place to grip the casing to remove
it from the chamber once fired;
5. primer, which ignites the propellant.
No comments:
Post a Comment